Home > Engine Parts > Exhaust Systems > Cessna Power Flow >

Cessna 180 (Pre 1955) Aircraft Exhaust Power Flow Systems
Cessna 180 (Pre 1955) Aircraft Exhaust Power Flow Systems
Cessna 180 (Pre 1955) Aircraft Exhaust Power Flow Systems
 
Alternative Views:


Please email [email protected] for pricing on Power Flow products. Prices fluctuate too frequently to remain current. Include registration number and engine make and model.

Bolt-On Horsepower.
Complete replacement of your exhaust system. FAA approved by STC for all Pre '55 Cessna 180 aircraft

The model aircraft it was approved for have serial numbers 604, 615 and 30000 through 32661 that are equipped with FAA approved installation instructions of Continental O-470 K, L, R or S model engines. Note: Please let us know if you have the “ tilt down seaplane mount” P/N 0751003-31

  • Make your Cessna 180 a faster, higher flying bird. Similar technology has been used in race cars and motorcycles for years, now it is available for your Cessna 180. By more effectively emptying the cylinders of spent exhaust gases, this high performance exhaust system immediately gives your Cessna 180 the following improvements:

  • An increase of rpm in static thrust

  • A take-off roll that is measurably shorter

  • An improvement in the aircraft’s rate of climb

  • An increase in Cruise Speed.

  • CHT’s that are cooler across the board.

  • A Service Ceiling that is higher, with a corresponding improvement in performance at higher density altitudes

  • The back pressure has been greatly reduced with the 1-3/4″ primary tubes being large enough to handle a 550 engine. The primary tubes also incorporate a slip joint to accommodate expansion and contraction and do away with the original 2 part 1-1/2″ beaded end risers that were inherent to leakage and very difficult to remove.


Visit Blue Skies Aviation, a PowerFlow Systems Risk Free Guarantee Installation Center.



Product Code: PFS-CESSNA-180-PRE55
Email For Pricing

Features Information
 
Features
Performance improvements:

- 3-7 knots faster (3 knots is minimum guarantee)

- Up to 1.5 gallons per hour fuel savings at current speeds

- Up to 20% improvement in rate of climb

- Increase in service ceiling �� 2000-5000 feet

Exhaust Features:
An entirely new high performance tuned exhaust system, includes Power Flow��s patented and patent pending design features such as:

- Each header has an independent slip joint �� no clamps

- No complicated bracketry for the exhaust (unlike the stock)

- Mandrel bent tubing

- 2 heating sources (like the original exhaust)

- Weighs approximately 2 pounds less than the stock design (final design may be different)

- 1 year/500 hour warranty, whichever occurs first (2 year/500hr if you perform a dynamic balance within 25 hours of installation)

- Includes all necessary hardware and SCAT tubing for installation. No need to purchase anything additional.

- Muffler that has easily replaceable components �� doesn��t require an overhaul by a repair station

- PFS exhaust exits out same hole in cowling

- Estimated time to remove stock exhaust and install PFS: 6-8 hours

Performance Data - Power Flow's Test Bed

11500 Feet
Speed Increase Fuel Burn Change

+6 Knots @ 2200RPM 0 GPH Less
+3 Knots @ 2500RPM 1.3 GPH Less
+4 Knots @ 2700RPM 1.3 GPH Less
8500 Feet
Speed Increase Fuel Burn Change

+3 Knots @ 2400RPM 0.4 GPH Less
+4 Knots @ 2500RPM 0 GPH Less
+4 Knots @ 2700RPM 0.7 GPH Less
2500 Feet
Speed Increase Fuel Burn Change

+3 Knots @ 2300RPM 0.8 GPH More
+3 Knots @ 2500RPM 0.6 GPH More
+3 Knots @ 2700RPM 0.4 GPH More

Share your knowledge of this product. Be the first to write a review »